2019 Fiat 124 Spider Key Replacement

2019 124 Spider key specs

Every US 124 Spider starts with a button and uses a four-button smart key (lock, unlock, trunk and panic) with FCC ID WAZSKE13D01 or WAZSKE13D02 on the back. A mechanical emergency key hides inside the fob for the driver's door if the battery dies, and each car comes with a plate stamped with that key's code number. Read the FCC ID and part number on your own fob before buying, and avoid used fobs, which may already be locked to another car.

What's specific to the 2019 124 Spider

The 2019 Fiat 124 Spider is the third of 4 model years in the 124 Spider Type 348 (Mazda-built) (2017–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2019 Fiat 124 Spider is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2019 124 Spider can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Fiat 124 Spider

• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Fiat 124 Spider open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Fiat immobilizer works on the 124 Spider

Fiat returned to the US for the 2012 model year, and every Fiat sold here since has a transponder immobilizer that must recognize the key before the engine will keep running. The Mexican-built 500 and 500c use a Philips ID46 (Hitag 2) chip in a three-button flip key, paired with a Delphi-type body computer. The Serbian-built 500L uses the same chip family but a Magneti Marelli-type body computer, so its remote is not interchangeable with the 500's. The Italian-built 500X steps up to AES encryption: a Megamos AES chip in the early flip key and Hitag AES in the push-button smart key, which is the only style Fiat's owner's manuals describe from 2017 on. The 124 Spider is the outlier, built by Mazda in Hiroshima with a Mazda-designed smart key running at 315 MHz. The first-generation 500e shares the 500's turn-key setup, while the 2024 and newer 500e uses a newer Stellantis keyless system. On the 500, 500L and 500X, the mechanical blade is the SIP22 laser-cut profile. When the chip isn't recognized, the blade can still turn the ignition, but the immobilizer will not let the engine run.

• Mazda built the 124 Spider in Hiroshima alongside the MX-5 Miata, and its fob carries a Mazda-style FCC ID rather than a Fiat or Chrysler one.
• Its smart key runs at 315 MHz, while other US Fiat remotes of the era use the 433 MHz band.
• The fob takes a CR2025 coin cell, thinner than the CR2032 used in 500-family keys.
• The 2020 model year was the last for the 124 Spider in the US.

Programming a 2019 124 Spider key

Because Mazda supplied the keyless system, programming usually follows Mazda-style smart-key routines through the OBD-II port rather than the Fiat PIN procedure used on the 500 family. Many of these routines erase and re-learn every fob in one session, so bring all the fobs you have. Equipment coverage for the Fiat-badged car is narrower than for the MX-5, and we confirm the VIN before quoting.

Spare fobs are usually possible. All-keys-lost and tool coverage vary for this Mazda-built Fiat, so some cases go to a dealer.

Lost every key to your 124 Spider?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Fiat 124 Spider can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2019 Fiat 124 Spider we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

124 Spider key battery

Most fobs for a 2019 Fiat 124 Spider open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2025, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 124 Spider uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Fiat keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 124 Spider, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 124 Spider key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 124 Spider came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Fiat system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Fiat key problems

• A key that turns but won't start the engine usually means the immobilizer doesn't recognize its transponder: a damaged chip, a key programmed to another car, or a spare that lost its pairing. Reprogramming fixes it; the ignition is rarely at fault.
• Buying the wrong remote is a frequent mistake. The 500 and 500c use Delphi-type remotes marked LTQF12AM433TX or 2ADFTF12AM433TX, while the 500L uses the Marelli-type 2ADPXTRF198. The blades match, but the buttons only work on the right car.
• Inexpensive online Fiat flip keys often arrive locked or uncoded. Many must be pre-coded on a key programmer before the car will learn them, so a key that won't program is often the wrong blank rather than a fault in the car.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2019 Fiat 124 Spider key?

Don't wait until the last key disappears. If your Fiat 124 Spider is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.