Chrysler Sebring Key Replacement

Sebring keys by generation

The redesigned Sebring arrived as a 2007 sedan, with the convertible following for 2008. Both use a remote-head key on the Y159 keyway with a Philips ID46 chip, listed under FCC ID OHT692427AA, or OHT692713AA and OHT692714AA on some cars with remote start. Convertible keys can carry extra buttons for the power top, which can be lowered from the fob. A plain ID46 transponder key without buttons will also start the car and works well as a spare. Keys and remotes are programmed over OBD-II with the 4-digit PIN; the chip and the buttons on a remote-head key can be learned as separate steps. Supplier listings describe an on-board routine for these years when two working keys are on hand. When all keys are lost, a blade is cut by code or from a decoded lock and both functions are programmed at the vehicle.

Sedans and convertibles from this generation use a Y159-keyway transponder key with a 4D64 chip and a separate four-button fob (lock, unlock, trunk, panic) listed under FCC ID GQ43VT17T. The fob takes a CR2016 battery. Supplier listings note that this remote does not fit the Sebring coupe of the same years, which uses Mitsubishi hardware. If your car never had a fob, only the transponder key is needed to drive it. Keys are programmed through the OBD-II port to the Sentry Key module using the 4-digit PIN, which current tools can typically read on this platform. Supplier listings confirm an on-board learning sequence for the GQ43VT17T fob when one working remote is available. For all keys lost, we originate a key by code or lock decoding and program it wherever the car is parked.

For 2000, a Sebring on this page means the JX convertible, since the sedan had not arrived yet. Its ignition key is the Chrysler Y159-keyway blade, and supplier catalogs list a 4D64 transponder key (Ilco Y160-PT blank) for Sebring convertibles from 1998 on, though plain Y159 keys are also catalogued, so equipment can vary. Keyless entry, where equipped, used a separate fob rather than buttons in the key. We read the original key's chip before cutting to confirm the match. Keys are programmed to the Sentry Key module through the OBD-II port with the 4-digit PIN, and a 4D64 clone is possible if you have a working key to copy. If you have no key at all, we cut one by code or by decoding a lock and program it on site. A replacement fob, on cars with keyless entry, is matched to the car after the key is working.

Chrysler key security

Chrysler began fitting its Sentry Key Immobilizer System (SKIS) in the late 1990s, and by the 2001 model year most Chryslers in our range used it. The first wave of keys carried a Texas Instruments 4D64 chip in a head cut for the Y159-family keyway, sold as the Ilco Y160-PT blank. From about 2004 the chip changed to a Philips ID46, and most cars paired it with a remote-head key that put the transponder and the keyless entry buttons in one piece. For 2008 the 300 and Town & Country moved to the fobik, a blade-less remote that turns inside a wireless ignition node (WIN), with a proximity version for push-button start. The 2011 redesign of the 300 added a proximity smart key, and the Pacifica minivan, the 2015–2017 200 and the 2019–2023 300 use fobs with Hitag AES encryption. Vehicles from 2018 on also carry a secure gateway module that limits what aftermarket tools can write. Two models break the pattern: the Mitsubishi-built Sebring coupe uses a 4D61 chip and a Mitsubishi blade, and the Mercedes-based Crossfire uses an HU64 flip key with Mercedes immobilizer electronics.

Most Chrysler key work runs through the OBD-II port and a 4-digit security PIN tied to the vehicle. Current programmers can read that PIN from the immobilizer on many older models; on others it comes from the dealer by VIN, which requires proof of ownership. Many cars through about 2010 also have an owner-level key-learn routine, but it needs two working keys already in hand, so it is no help once you are down to one or none. A remote-head key can need the chip and the buttons learned in separate steps, so a key that starts the engine may still need its remote side set up. Most 2011 and newer remotes need a programming tool. On 2018 and newer vehicles, the secure gateway module adds a bypass cable or authenticated login to every job. Before we cut or program anything we verify your ID and ownership, and we quote the whole job, including key, cutting and programming, before starting.

All Sebring keys lost

Losing every key is usually recoverable on a Chrysler without towing it to a dealer. For bladed keys, we decode a door lock or cut by code from the VIN record after confirming you own the vehicle, then program a new transponder or remote-head key through the OBD-II port. Fobik-equipped vans and sedans need no ignition cut, so that work is mostly electronic plus a new emergency insert for the door. The harder cases are the AES-encrypted smart keys on the Pacifica, Voyager, 2015–2017 200 and 2019–2023 300, where some vehicles need the radio frequency hub handled directly or a dealer visit, and the Crossfire, whose Mercedes-derived keys are normally ordered pre-coded. We tell you which case applies before we drive out.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Chrysler Sebring requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Sebring and your schedule.

How the job works

1. Identify the exact key your Sebring uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chrysler Sebring keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Sebring, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Sebring key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Sebring key types explained

• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Chrysler Sebring only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.
• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2010 Sebring, we open the old key and show you what's broken before recommending anything.
• Key with separate remote fob. Separate remotes are easy to find online, which is exactly why they cause trouble. A listing can show the same shell as your Chrysler Sebring remote while hiding a different FCC ID, frequency or internal chip, and some used remotes are locked to the first vehicle they were paired with. We're glad to look at one you've already bought, and we'll tell you honestly whether it can be paired before charging you to try. If the remote side of your setup has become unreliable, it's also worth asking whether a fresh remote and a newly cut key, matched together, would cost less than chasing repairs on aging parts.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Tips from a mobile locksmith

• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Common Chrysler key problems

• Worn Y159 ignition keys on older minivans, PT Cruisers and LH sedans can stop turning smoothly or bind in the cylinder. Copying a worn key copies the wear, so we cut replacements to the original code rather than tracing the old blade.
• On 2008–2016 Town & Country vans and 2008–2010 300s, a fobik that will not turn or is not recognized may be a worn fob or a failing wireless ignition node. We test with a known-good fob before anyone replaces parts.
• Remote-head keys from the 2004–2014 era often crack where the blade meets the plastic head. A new shell can save the electronics, but the transponder chip has to move with them or the car will not stay running.
• A remote that only works from a few feet away usually needs a fresh battery. Fobs from 1999–2006 use CR2016 coin cells, while most later remote-head keys, fobiks and smart keys take a single CR2032. Inland summer heat is hard on these cells, so the battery is the first check.
• Remotes bought online for 2004 and later Chryslers still have to be paired to the car. Some cars through about 2010 can learn one at home if you hold two working keys; otherwise it takes a programming tool, and used fobs must be unlocked first.
• On 2018 and newer Chryslers, the secure gateway module blocks many aftermarket scan tools. Key programming still works with a bypass cable or authenticated access, which is why a shop without that setup may tell you only the dealer can help.
• The 2018 and 2019 Chrysler 300 smart keys look identical but carry different transponder chips and different FCC IDs, M3N-40821302 versus M3M-40821302. Ordering by appearance alone leads to a fob that will not program, so match the model year and part number.
• Sebring orders get mixed up often: the sedan and convertible use Chrysler keys and fobs, while the 2001–2005 Sebring coupe uses Mitsubishi-based keys and remotes that fit none of the other Sebrings.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.