2001 Chrysler LHS Key Replacement

2001 LHS key specs

An LHS key is a Y159-keyway blade with a 4D64 transponder, the pattern sold as the Ilco Y160-PT blank. Keyless entry uses a separate four-button fob with lock, unlock, trunk and panic. The 2000 fob is FCC ID GQ43VT9T and the 2001 fob is GQ43VT17T, so the model year matters when ordering a remote, even though the two look much alike. Both take CR2016 batteries.

What's specific to the 2001 LHS

2001 was the final model year of the LHS LH (2nd generation). Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2001 Chrysler LHS matches a 2000. A 2001 Chrysler LHS is about 25 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

If a newly cut key turns the 2001 LHS's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2001 Chrysler LHS

• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Chrysler LHS, we'll explain which method fits and why.
• Key with separate remote fob. Some Chrysler LHS owners carry two pieces: a transponder key for the ignition and a separate remote fob on the same ring. Because they work independently, you only have to replace what's actually missing or broken. A lost remote still leaves you with a key that opens the doors and starts the engine, so it's an inconvenience rather than an emergency. A lost key is the more urgent half, since it has to be cut and its chip programmed before the car will run. We stock and program both sides, and if the whole ring is gone, we handle the key first and then pair a new remote.

How the Chrysler immobilizer works on the LHS

Chrysler began fitting its Sentry Key Immobilizer System (SKIS) in the late 1990s, and by the 2001 model year most Chryslers in our range used it. The first wave of keys carried a Texas Instruments 4D64 chip in a head cut for the Y159-family keyway, sold as the Ilco Y160-PT blank. From about 2004 the chip changed to a Philips ID46, and most cars paired it with a remote-head key that put the transponder and the keyless entry buttons in one piece. For 2008 the 300 and Town & Country moved to the fobik, a blade-less remote that turns inside a wireless ignition node (WIN), with a proximity version for push-button start. The 2011 redesign of the 300 added a proximity smart key, and the Pacifica minivan, the 2015–2017 200 and the 2019–2023 300 use fobs with Hitag AES encryption. Vehicles from 2018 on also carry a secure gateway module that limits what aftermarket tools can write. Two models break the pattern: the Mitsubishi-built Sebring coupe uses a 4D61 chip and a Mitsubishi blade, and the Mercedes-based Crossfire uses an HU64 flip key with Mercedes immobilizer electronics.

• The 2001 model year was the last for the LHS; the 300M continued as Chrysler's LH flagship through 2004.
• Supplier fitment for the GQ43VT9T remote spans the 1998–2000 LHS, Concorde and 300M, while the 2001 LHS moved to GQ43VT17T.

Programming a 2001 LHS key

New keys are written to the immobilizer module over OBD-II with the 4-digit PIN, and current programmers can typically retrieve that PIN from the module on these cars. The 2001 fob can be added with the on-board sequence if one working remote is on hand. With no keys at all, we originate a key by code or lock decoding and program it at your location.

Lost every key to your LHS?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2001 Chrysler LHS we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

LHS key battery

Battery details for the 2001 LHS: CR2016 (remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your LHS uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chrysler keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Chrysler system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an LHS key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Chrysler LHS is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chrysler key problems

• Sebring orders get mixed up often: the sedan and convertible use Chrysler keys and fobs, while the 2001–2005 Sebring coupe uses Mitsubishi-based keys and remotes that fit none of the other Sebrings.
• Remote-head keys from the 2004–2014 era often crack where the blade meets the plastic head. A new shell can save the electronics, but the transponder chip has to move with them or the car will not stay running.
• A remote that only works from a few feet away usually needs a fresh battery. Fobs from 1999–2006 use CR2016 coin cells, while most later remote-head keys, fobiks and smart keys take a single CR2032. Inland summer heat is hard on these cells, so the battery is the first check.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2001 Chrysler LHS key?

The quickest route to a working key for a 2001 Chrysler LHS starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.