2000 Chrysler Concorde Key Replacement

2000 Concorde key specs

The Concorde's ignition key is a Y159-keyway blade with a 4D64 transponder in the head, sold as the Ilco Y160-PT blank. Keyless entry uses a separate four-button fob: FCC ID GQ43VT9T for 2000 and GQ43VT17T for 2001–2004, both powered by CR2016 batteries and both with lock, unlock, trunk and panic buttons. If your Concorde never had a fob, only the transponder key is needed to drive it.

What's specific to the 2000 Concorde

2000 was the first model year of the Concorde LH (2nd generation). Early-production cars sometimes use different part numbers than later ones, so for a 2000 Chrysler Concorde we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. A 2000 Chrysler Concorde is about 26 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

If a newly cut key turns the 2000 Concorde's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2000 Chrysler Concorde

• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Chrysler Concorde, we'll explain which method fits and why.
• Key with separate remote fob. Some Chrysler Concorde owners carry two pieces: a transponder key for the ignition and a separate remote fob on the same ring. Because they work independently, you only have to replace what's actually missing or broken. A lost remote still leaves you with a key that opens the doors and starts the engine, so it's an inconvenience rather than an emergency. A lost key is the more urgent half, since it has to be cut and its chip programmed before the car will run. We stock and program both sides, and if the whole ring is gone, we handle the key first and then pair a new remote.

How the Chrysler immobilizer works on the Concorde

• Supplier fitment for the Y160-PT transponder key covers the 1998–2004 Concorde, matching the 300M.
• The 2001–2004 GQ43VT17T remote is shared with the 300M, the 2001 LHS and the Sebring sedan and convertible.
• The Concorde ended after 2004 and was succeeded by the rear-drive 300.

Programming a 2000 Concorde key

Programming runs through the immobilizer module via the OBD-II port and needs the 4-digit PIN, which current tools can usually pull on this platform. The 2001–2004 remote supports an on-board learning sequence when you already have one working fob. Without any working key, we cut a blade by code or from the door lock and program it on site.

Lost every key to your Concorde?

Losing every key is usually recoverable on a Chrysler without towing it to a dealer. For bladed keys, we decode a door lock or cut by code from the VIN record after confirming you own the vehicle, then program a new transponder or remote-head key through the OBD-II port. Fobik-equipped vans and sedans need no ignition cut, so that work is mostly electronic plus a new emergency insert for the door. The harder cases are the AES-encrypted smart keys on the Pacifica, Voyager, 2015–2017 200 and 2019–2023 300, where some vehicles need the radio frequency hub handled directly or a dealer visit, and the Crossfire, whose Mercedes-derived keys are normally ordered pre-coded. We tell you which case applies before we drive out.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Chrysler Concorde, ask us directly and you'll get a plain answer.

Concorde key battery

Battery details for the 2000 Concorde: CR2016 (remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Concorde uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chrysler Concorde keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chrysler keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Chrysler system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Concorde key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chrysler key problems

• Remote-head keys from the 2004–2014 era often crack where the blade meets the plastic head. A new shell can save the electronics, but the transponder chip has to move with them or the car will not stay running.
• Remotes bought online for 2004 and later Chryslers still have to be paired to the car. Some cars through about 2010 can learn one at home if you hold two working keys; otherwise it takes a programming tool, and used fobs must be unlocked first.
• A remote that only works from a few feet away usually needs a fresh battery. Fobs from 1999–2006 use CR2016 coin cells, while most later remote-head keys, fobiks and smart keys take a single CR2032. Inland summer heat is hard on these cells, so the battery is the first check.
• On 2008–2016 Town & Country vans and 2008–2010 300s, a fobik that will not turn or is not recognized may be a worn fob or a failing wireless ignition node. We test with a known-good fob before anyone replaces parts.

Tips from a mobile locksmith

• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2000 Chrysler Concorde key?

Need a key for your 2000 Chrysler Concorde? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.