2025 Cadillac CT4 Key Replacement

2025 CT4 key specs

Every CT4 starts with a push button and a proximity fob; there is no key ignition. Fobs from this generation commonly carry FCC ID YG0G20TB1, and later cars may show a revised part number, so check the back of your fob. Most are five-button units covering lock, unlock, trunk, remote start and panic, and each holds a mechanical emergency key for the driver's door. CT4-V and Blackwing models use the same style of fob as the standard sedan.

What's specific to the 2025 CT4

The 2025 Cadillac CT4 is the sixth of 7 model years in the CT4 First generation (2020–2026), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At 1 year old, a 2025 Cadillac CT4 is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Smart-key cars like the 2025 CT4 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2025 Cadillac CT4

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Cadillac CT4 First generation, we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Cadillac immobilizer works on the CT4

Cadillac has used almost every generation of General Motors theft deterrent since 2000, so the key in your hand depends heavily on the model year. The last Eldorados relied on a resistor pellet in the key blade, which the car reads as a resistance value rather than a code. DeVille, Seville and early CTS cars use PASS-Key III, a transponder chip molded into the key head. Escalades built before 2007 took a different path: Passlock, where the sensor lives in the ignition lock cylinder and the key itself carries no chip. Later turn-key cars moved to PASS-Key III+ with a Philips ID46-family chip, while the XLR in 2004 and the STS in 2005 brought Keyless Access fobs and push-button start to the lineup. Proximity fobs then spread across nearly every model, and many of them can be learned on-board in about 30 minutes. Starting with the 2020 CT4 and CT5 and the 2021 Escalade, GM's Global B electrical architecture brought Hitag Pro fobs and encrypted programming, and newer cars increasingly need a professional programmer. The Ultium electric models, from the Lyriq onward, add another layer. Before we quote, we confirm the year, model and key style so you know exactly what the job involves.

• The CT4 and CT5 were among the first Cadillacs built on the Global B electrical architecture.
• CT4 fobs take a CR2450 coin cell, larger than the CR2032 used in earlier Cadillac fobs.
• Production of the CT4 ended in mid-2026, and Cadillac has not named a direct successor.

Programming a 2025 CT4 key

The CT4 sits on GM's Global B architecture. On early cars, a new fob can be learned on-board from the Driver Information Center when two working fobs are present. Newer cars, and any lost-key job, call for a professional programmer that can obtain GM's online authorization. Adding a spare is often possible with current tools when the car is present and you can show proof of ownership. All-keys-lost is less predictable and may end at the dealer. We tell you which path your car needs before any work starts.

Global B encryption; spare fobs are often doable, but some all-keys-lost jobs need the dealer.

Lost every key to your CT4?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2025 Cadillac CT4 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

CT4 key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2450 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your CT4 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Cadillac keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your CT4, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a CT4 key

• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Cadillac system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Cadillac key problems

• High-mileage DTS and DeVille sedans develop worn ignition cylinders that make the key stick or refuse to turn. Copying a worn key copies the wear, so we prefer to cut a fresh key by code.
• Aftermarket remote starters on older Cadillacs often rely on a bypass module wired into the key system. When that module fails, the car can act as if the correct key is wrong, which looks like a key problem but is not.
• When a fob battery dies completely, many push-button Cadillacs will still start with the fob held in the backup pocket or spot shown in the owner's manual. Many owners never look for it until the day they need it.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2025 Cadillac CT4 key?

The quickest route to a working key for a 2025 Cadillac CT4 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.