2013 Cadillac ATS Key Replacement

2013 ATS key specs

The ATS uses Keyless Access with push-button start, so there is no ignition slot to cut a key for. 2013 and 2014 cars typically carry a GM proximity fob with FCC ID NBG009768T, while 2015 and later cars are mostly fitted with the slimmer HYQ2AB fob, and HYQ2EB fobs are also listed for late cars. Button layouts follow the options on the car: lock, unlock, trunk and panic on most, plus remote start where equipped. Each fob hides a mechanical emergency blade that works the cylinder under a cap on the driver's door handle. Coupes and ATS-V models use the same key hardware as the sedan.

What's specific to the 2013 ATS

2013 was the first model year of the ATS First generation (sedan and coupe). Early-production cars sometimes use different part numbers than later ones, so for a 2013 Cadillac ATS we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. At roughly 13 years old, a 2013 Cadillac ATS has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2013 ATS can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2013 Cadillac ATS

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2013 Cadillac ATS is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Cadillac immobilizer works on the ATS

Cadillac has used almost every generation of General Motors theft deterrent since 2000, so the key in your hand depends heavily on the model year. The last Eldorados relied on a resistor pellet in the key blade, which the car reads as a resistance value rather than a code. DeVille, Seville and early CTS cars use PASS-Key III, a transponder chip molded into the key head. Escalades built before 2007 took a different path: Passlock, where the sensor lives in the ignition lock cylinder and the key itself carries no chip. Later turn-key cars moved to PASS-Key III+ with a Philips ID46-family chip, while the XLR in 2004 and the STS in 2005 brought Keyless Access fobs and push-button start to the lineup. Proximity fobs then spread across nearly every model, and many of them can be learned on-board in about 30 minutes. Starting with the 2020 CT4 and CT5 and the 2021 Escalade, GM's Global B electrical architecture brought Hitag Pro fobs and encrypted programming, and newer cars increasingly need a professional programmer. The Ultium electric models, from the Lyriq onward, add another layer. Before we quote, we confirm the year, model and key style so you know exactly what the job involves.

• 2013-2014 ATS fobs belong to the NBG009768T family also used on the early XTS and the 2014 ELR.
• From 2015 the ATS fob is mostly the HYQ2AB design, which shares its FCC ID with fobs on the CTS, XTS and Escalade of those years, though button layouts differ.
• A fob with a weak battery can still start the car from the backup location described in the owner's manual.

Programming a 2013 ATS key

We add ATS fobs through the OBD-II port with a professional programmer, or with GM's on-board learn: with the cap off the driver's door handle, the key cylinder is turned to unlock five times, and the new fob goes in the console pocket. GM's security wait applies either way. With all keys lost, we cut an HU100 emergency blade to your door lock, then run the roughly 30-minute relearn, which drops any fob not present so it can no longer start the car. Have proof of ownership ready.

Lost every key to your ATS?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Cadillac ATS, ask us directly and you'll get a plain answer.

ATS key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your ATS uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Cadillac keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your ATS, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an ATS key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your ATS came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Cadillac system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Cadillac key problems

• CT4, CT5 and 2021-and-later Escalade fobs use encrypted Global B programming, so a bargain fob bought online may never program. Match the FCC ID, frequency and part number on your current fob before buying anything.
• A flashing security light and a crank-no-start on a 2002-2006 Escalade often points to a failing Passlock sensor in the ignition cylinder rather than the key. A relearn may bring it back for a while, but the sensor or cylinder usually needs repair.
• Cadillac proximity fobs usually show a low-battery or remote-not-detected message on the Driver Information Center well before they quit. Replacing the coin cell at the first warning avoids a no-start in a parking lot.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2013 Cadillac ATS key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your ATS in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.