2016 BMW M6 Key Replacement

2016 M6 key specs

The second M6 uses BMW's F-series smart fob with push-button start and no dash slot. The fob holds an ID49 transponder, remote buttons and a slide-out emergency blade, and Comfort Access was offered. The F13 coupe, F12 convertible and F06 Gran Coupe share one key system with the 650i of the same years. The coupe was sold through 2017, the convertible through 2018 and the four-door Gran Coupe through 2019.

What's specific to the 2016 M6

The 2016 BMW M6 is the fourth of 7 model years in the M6 F06/F12/F13 (third generation) (2013–2019), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 10 years old, a 2016 BMW M6 has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2016 M6 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2016 BMW M6

• Smart proximity key (push-to-start). A smart or proximity key lets a 2016 BMW M6 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the BMW immobilizer works on the M6

BMW has changed its key technology roughly once a decade, so the build date tells us more about the job than the badge on the trunk. In 2000, the 3, 5 and 7 Series, the X5 and the Z3 all used the EWS immobilizer: a diamond-shaped remote key with a Philips ID44-family transponder, checked by an EWS module that trades a rolling code with the engine computer. The key blade is a two-track or four-track design depending on the model. The 2002 7 Series introduced the Car Access System (CAS), and over the next decade CAS2, CAS3 and CAS3+ spread across the lineup with a rectangular fob that slides into a dash slot before you press Start/Stop. F-series cars from 2009 dropped the slot for Hitag Pro (ID49) smart fobs, stored in a CAS4 module on the 5, 6 and 7 Series and X3, and in a front electronic module (FEM) or body domain controller (BDC) on the 2, 3 and 4 Series, X5 and i3. G-series models from 2016 kept the BDC idea and, from mid-2020 builds, added BMW Digital Key for phones. The newest electronics, found on the current 7 and 5 Series, the electric i models and several recent redesigns and facelifts, are still dealer territory for new keys.

• The M6 Gran Coupe was the only four-door M6, and it outlived the coupe by two model years in the US.
• A missing fob can be deleted from the CAS during the same visit that adds a new one.

Programming a 2016 M6 key

Keys are stored in the Car Access System, usually the CAS4+ version on these cars. The module normally comes out for a bench read, after which we write the fob with the car's data, finish its learning step through the OBD-II port and check keyless entry if equipped. All-keys-lost uses the same approach once the emergency blade has been cut by code.

Lost every key to your M6?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your BMW M6 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your BMW M6 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your BMW M6, ask us directly and you'll get a plain answer.

M6 key battery

If a new CR2450 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your M6 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the BMW system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an M6 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your M6 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common BMW key problems

• Comfort Access lets the fob stay in your pocket, but it also exposes the car to relay theft. Storing keys away from the front door, or in a signal-blocking pouch, lowers that risk on smart-key BMWs.
• Diamond-shaped remote keys on EWS-era BMWs recharge their cell only while the key sits in the ignition. A spare left in a drawer for months often loses its buttons, yet it still starts the car because the transponder needs no battery.
• Smart fobs announce a weak coin cell with shorter range or a key-not-detected message at startup. Every model has a backup spot, shown in the owner's manual, where holding the fob lets the car read it and start anyway.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2016 BMW M6 key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your M6 in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.