BMW i8 Key Replacement

i8 keys by generation

For 2019 and 2020, the i8 came as a coupe and as the new I15 Roadster with a power soft top. Both start the same way, with a smart fob inside the car and a press of Start/Stop. BMW lists different fob part numbers for these cars than for the 2014-2017 coupe, so an early fob is not a safe swap even though the cars look nearly identical. Bring every working fob to the appointment, because programming rewrites the list of keys the car will accept. Like the earlier car, the updated i8 stores its keys in the body domain controller. We read that module, usually on the bench after removing it, prepare a new fob with the car's data and finish the learning step through the OBD-II port. Whether all-keys-lost can be done outside a dealer depends on the module's software, which BMW revised over time. We confirm coverage by VIN before you order a fob, and we tell you plainly if the dealer is the better route.

Every 2014-2017 i8 starts with the fob anywhere in the cabin and a press of the Start/Stop button; there is no key slot and no ignition cylinder. The fob holds the remote buttons and a Hitag Pro transponder, which the car can still read at very close range when the fob battery is weak. BMW gave the i8 its own fob part numbers, separate from the X1, X5 and other models of the same years, so a fob from another BMW is not a substitute. We match a replacement to your VIN before ordering. The i8 keeps its key data in the body domain controller (BDC), the module that also runs locking and lighting. Adding a fob means reading that module, occasionally through the OBD-II port but more often on a programmer after it is removed, then preparing the new fob and teaching it to the car. Some procedures also need data from the engine computer. All-keys-lost follows the same steps, but coverage depends on the module's software level, so we check the VIN first.

BMW key security

BMW has changed its key technology roughly once a decade, so the build date tells us more about the job than the badge on the trunk. In 2000, the 3, 5 and 7 Series, the X5 and the Z3 all used the EWS immobilizer: a diamond-shaped remote key with a Philips ID44-family transponder, checked by an EWS module that trades a rolling code with the engine computer. The key blade is a two-track or four-track design depending on the model. The 2002 7 Series introduced the Car Access System (CAS), and over the next decade CAS2, CAS3 and CAS3+ spread across the lineup with a rectangular fob that slides into a dash slot before you press Start/Stop. F-series cars from 2009 dropped the slot for Hitag Pro (ID49) smart fobs, stored in a CAS4 module on the 5, 6 and 7 Series and X3, and in a front electronic module (FEM) or body domain controller (BDC) on the 2, 3 and 4 Series, X5 and i3. G-series models from 2016 kept the BDC idea and, from mid-2020 builds, added BMW Digital Key for phones. The newest electronics, found on the current 7 and 5 Series, the electric i models and several recent redesigns and facelifts, are still dealer territory for new keys.

No BMW in this range lets an owner add a key from the driver's seat, so every new key or fob is written with professional equipment, and the car's era decides how. EWS cars usually need the module removed and read on a programmer. CAS2, CAS3 and early CAS4 cars can often be handled through the OBD-II port, while CAS3+ and CAS4+ modules running later BMW software are commonly read on the bench. FEM and BDC cars almost always mean taking the module out, backing up its data and preparing it before a key can be added, and all-keys-lost work also needs the engine computer's ISN. BMW fobs lock to the first car they are coded to, so a used fob only works if it can be professionally renewed. Bring every key you have, since some procedures rewrite the stored key list, and expect us to check your ID and registration before we start.

All i8 keys lost

With every key gone, most BMWs built before the newest electronics can still be keyed where they sit. We verify your ID and proof of ownership first. Then we get a working blade: on EWS cars that means cutting a key by code or by decoding the driver's door lock, and on slot-key and smart-fob cars it means cutting the emergency blade so the door opens mechanically. Next, we read the immobilizer module, through OBD-II where possible and on the bench where not, collect the engine computer's ISN when the system calls for it, and write new keys into the car. The lost keys are deleted so they can no longer start it. For models on BMW's newest platform, and some late body-module software, the dealer is the only route, and we'll tell you so before any work begins.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your BMW i8 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your i8 and your schedule.

How the job works

1. Identify the exact key your i8 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the BMW system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an i8 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your i8 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the BMW system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

i8 key types explained

• Smart proximity key (push-to-start). A smart or proximity key lets a 2020 BMW i8 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Common BMW key problems

• Diamond-shaped remote keys on EWS-era BMWs recharge their cell only while the key sits in the ignition. A spare left in a drawer for months often loses its buttons, yet it still starts the car because the transponder needs no battery.
• On slot-key BMWs from roughly 2002 to 2013, a fob the dash won't accept or recognize points to either a failing key or a faulty slot. Trying your spare first tells you which side has the problem before parts are ordered.
• Smart fobs announce a weak coin cell with shorter range or a key-not-detected message at startup. Every model has a backup spot, shown in the owner's manual, where holding the fob lets the car read it and start anyway.
• Used BMW fobs from online sellers are locked to the car they came from. Some can be professionally renewed and recoded, many cannot, so send us the part number and FCC ID before you buy one.
• A weak 12-volt battery can make a healthy key look dead: the locks ignore the remote, Start/Stop does nothing and warnings pile up on the dash. Charge or test the battery before blaming the fob or the body module.
• Inland Empire summer heat shortens coin-cell life and can warp older key shells. Keep the spare indoors instead of in a hot glovebox, and replace a fob battery at the first sign of reduced range.
• Comfort Access lets the fob stay in your pocket, but it also exposes the car to relay theft. Storing keys away from the front door, or in a signal-blocking pouch, lowers that risk on smart-key BMWs.
• Installing a used engine computer or immobilizer module leaves a BMW that cranks but won't run. The two modules share a secret code, so the replacement has to be synchronized or adapted to the car first.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.