2016 BMW 6 Series Key Replacement

2016 6 Series key specs

The third-generation 6 Series uses BMW's F-series smart fob with push-button start and no dash slot. The fob holds an ID49 transponder, remote buttons and a slide-out emergency blade, and Comfort Access was offered. The F12 convertible and F13 coupe came first for 2012, and the four-door F06 Gran Coupe joined for 2013. The 640i, 650i and the M6 in all three body styles share the key system with the F10 5 Series and F01 7 Series of the same years.

What's specific to the 2016 6 Series

The 2016 BMW 6 Series is the fifth of 6 model years in the 6 Series F06/F12/F13 (third generation) (2012–2017), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 10 years old, a 2016 BMW 6 Series has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2016 BMW 6 Series

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your BMW 6 Series F06/F12/F13 (third generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the BMW immobilizer works on the 6 Series

BMW has changed its key technology roughly once a decade, so the build date tells us more about the job than the badge on the trunk. In 2000, the 3, 5 and 7 Series, the X5 and the Z3 all used the EWS immobilizer: a diamond-shaped remote key with a Philips ID44-family transponder, checked by an EWS module that trades a rolling code with the engine computer. The key blade is a two-track or four-track design depending on the model. The 2002 7 Series introduced the Car Access System (CAS), and over the next decade CAS2, CAS3 and CAS3+ spread across the lineup with a rectangular fob that slides into a dash slot before you press Start/Stop. F-series cars from 2009 dropped the slot for Hitag Pro (ID49) smart fobs, stored in a CAS4 module on the 5, 6 and 7 Series and X3, and in a front electronic module (FEM) or body domain controller (BDC) on the 2, 3 and 4 Series, X5 and i3. G-series models from 2016 kept the BDC idea and, from mid-2020 builds, added BMW Digital Key for phones. The newest electronics, found on the current 7 and 5 Series, the electric i models and several recent redesigns and facelifts, are still dealer territory for new keys.

• Because these cars share CAS4 with the F10 5 Series, the same OBD-II and bench procedures apply.
• A missing fob can be deleted from the CAS during the same visit that adds a new one.
• The four-door Gran Coupe was new to the 6 Series line with this generation.

Programming a 2016 6 Series key

Keys are stored in the Car Access System, CAS4 on earlier cars and CAS4+ on later ones. On many CAS4 cars a fob can be added through the OBD-II port; CAS4+ modules usually need to be removed and read on the bench first. We write the fob with the car's data, finish its learning step and check keyless entry if equipped. All-keys-lost uses the same approach once the emergency blade has been cut by code.

Lost every key to your 6 Series?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your BMW 6 Series can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2016 BMW 6 Series we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

6 Series key battery

Most fobs for a 2016 BMW 6 Series open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2450, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 6 Series uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two BMW 6 Series keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the BMW system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 6 Series key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 6 Series came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the BMW system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common BMW key problems

• A weak 12-volt battery can make a healthy key look dead: the locks ignore the remote, Start/Stop does nothing and warnings pile up on the dash. Charge or test the battery before blaming the fob or the body module.
• Installing a used engine computer or immobilizer module leaves a BMW that cranks but won't run. The two modules share a secret code, so the replacement has to be synchronized or adapted to the car first.
• Used BMW fobs from online sellers are locked to the car they came from. Some can be professionally renewed and recoded, many cannot, so send us the part number and FCC ID before you buy one.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2016 BMW 6 Series key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your 6 Series in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.