2007 BMW 5 Series Key Replacement

2007 5 Series key specs

The E60 brought BMW's slot key to the 5 Series: a rectangular fob pushed into the dash, then a press of Start/Stop. It carries an ID46 transponder, the remote buttons and a slide-out HU92 emergency blade, and Comfort Access was optional. The E61 Sports Wagon, the V10 M5 of 2006-2010 and the 535d all share it. One exception: the 2010 Gran Turismo is a different car built on the F07 platform, with a CAS4 smart fob like the later F10's.

What's specific to the 2007 5 Series

The 2007 BMW 5 Series is the fourth of 7 model years in the 5 Series E60/E61 (fifth generation) (2004–2010), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2007 BMW 5 Series is about 19 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Smart-key cars like the 2007 5 Series can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2007 BMW 5 Series

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2007 BMW 5 Series with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2007 BMW 5 Series open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the BMW immobilizer works on the 5 Series

BMW has changed its key technology roughly once a decade, so the build date tells us more about the job than the badge on the trunk. In 2000, the 3, 5 and 7 Series, the X5 and the Z3 all used the EWS immobilizer: a diamond-shaped remote key with a Philips ID44-family transponder, checked by an EWS module that trades a rolling code with the engine computer. The key blade is a two-track or four-track design depending on the model. The 2002 7 Series introduced the Car Access System (CAS), and over the next decade CAS2, CAS3 and CAS3+ spread across the lineup with a rectangular fob that slides into a dash slot before you press Start/Stop. F-series cars from 2009 dropped the slot for Hitag Pro (ID49) smart fobs, stored in a CAS4 module on the 5, 6 and 7 Series and X3, and in a front electronic module (FEM) or body domain controller (BDC) on the 2, 3 and 4 Series, X5 and i3. G-series models from 2016 kept the BDC idea and, from mid-2020 builds, added BMW Digital Key for phones. The newest electronics, found on the current 7 and 5 Series, the electric i models and several recent redesigns and facelifts, are still dealer territory for new keys.

• The CAS module changed from CAS2 to the CAS3 family around the 2008 facelift, so a 2006 and a 2009 car can need different procedures.
• Standard slot fobs recharge in the dash, so a spare that sits unused in a drawer can go flat.
• The E60 was the first 5 Series with a Start/Stop button in place of a turned key.

Programming a 2007 5 Series key

Earlier E60s use CAS2 and later cars CAS3 or CAS3+, all mounted under the dash. On most cars we read the module through the OBD-II port, build a fob from its data and write it into an empty key position, then test the slot, the remote and Comfort Access. Later CAS3+ modules with updated BMW software may need a bench read. All-keys-lost uses the same steps after the emergency blade is cut by code.

Lost every key to your 5 Series?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your BMW 5 Series can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your 5 Series and your schedule.

5 Series key battery

Keys for the 2007 5 Series use a rechargeable cell (Rechargeable cell (standard fob); CR2032 (Comfort Access fob)), so a weak key usually needs charging or replacement rather than a coin-cell swap. If range is still poor after charging, we can test the key and the car's receiver on site.

How the job works

1. Identify the exact key your 5 Series uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the BMW keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 5 Series, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 5 Series key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 5 Series came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common BMW key problems

• Smart fobs announce a weak coin cell with shorter range or a key-not-detected message at startup. Every model has a backup spot, shown in the owner's manual, where holding the fob lets the car read it and start anyway.
• Diamond-shaped remote keys on EWS-era BMWs recharge their cell only while the key sits in the ignition. A spare left in a drawer for months often loses its buttons, yet it still starts the car because the transponder needs no battery.
• Installing a used engine computer or immobilizer module leaves a BMW that cranks but won't run. The two modules share a secret code, so the replacement has to be synchronized or adapted to the car first.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2007 BMW 5 Series key?

Don't wait until the last key disappears. If your BMW 5 Series is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.