2017 Audi RS 7 Key Replacement

2017 RS 7 key specs

First-generation RS 7s have push-button start and a 4H0 959 754-family fob. The fob only needs to be inside the car, and keyless entry at the handles comes with advanced key. An emergency blade is stored in the fob for the driver's door. The electronics match the A7 and S7 fobs of the same type, so the badge on the case matters less than the part number.

What's specific to the 2017 RS 7

The 2017 Audi RS 7 is the fourth of 5 model years in the RS 7 4G (1st generation) (2014–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 9 years old, a 2017 Audi RS 7 has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2017 RS 7 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2017 Audi RS 7

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2017 Audi RS 7 is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Audi immobilizer works on the RS 7

• The RS 7 first arrived in the US for the 2014 model year.
• There were no 2019 or 2020 RS 7 models in the US.

Programming a 2017 RS 7 key

We program first-generation RS 7 keys through the BCM2-type comfort module, reading its data via OBD-II where the module version allows or on the bench where it doesn't. All-keys-lost requires removing the module. After learning, we confirm start, remote and keyless entry, and we keep the car on a battery maintainer during the work.

Audi key work starts with the VIN, because one model name can hide two different immobilizer generations in the same model year. On most Audis built before about 2017, adding a key is an adaptation session: the programmer reads immobilizer data through the OBD-II port or from a module on the bench, and on many of these cars every key you want to keep has to be present, because keys left out of the session stop starting the car. Dealer keys are made to order for your VIN. Aftermarket and refurbished keys must match the right chip, frequency and button layout, and some have to be prepared or unlocked before the car will accept them. Slot-start cars also need a healthy ignition slot, so we test it first. Before we cut or program anything, we check your ID against the registration or title, and when a particular year needs the dealer, we tell you that up front.

Spares are typically possible; all-keys-lost needs a bench read of the comfort module, and some units need the dealer.

Lost every key to your RS 7?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Audi RS 7, ask us directly and you'll get a plain answer.

RS 7 key battery

Most fobs for a 2017 Audi RS 7 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your RS 7 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Audi RS 7 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Audi system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an RS 7 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your RS 7 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Audi system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2017 Audi RS 7 key?

Don't wait until the last key disappears. If your Audi RS 7 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.